Amana PGD**C Manual de Instruções descarregar pdf (Página 2)

WARNING

PERSONAL INJURY HAZARD

To prevent death, personal injury or

property damage due to fire or explo-

sion caused by a propane gas leak, in-

stall a gas detecting warning device.

Since rust can reduce the level of odor-

ant in propane gas, a gas detecting warn-

ing device is the only reliable way to

detect a propane gas leak. Contact a

local propane gas supplier about install-

ing a gas detecting warning device.

IN CANADA THE CONVERSION SHALL BE CAR-

RIED OUT IN ACCORDANCE WITH THE REQUIRE-

MENTS OF THE PROVINCIAL AUTHORITIES HAV-

ING JURISDICTION AND IN ACCORDANCE WITH

THE REQUIREMENTS OF THE CAN/CGS B149.1 AND

B149.2 INSTALLATION CODE.

WARNING

PERSONAL INJURY HAZARD

To prevent death, serious personal in-

jury or property damage due to fire or

explosion caused by a propane gas leak,

install a gas detecting warning device.

If the propane gas furnace is installed in

a basement, an excavated area or a con-

fined space, a warning device is required

due to:

 Propane gas is heavier than air and

any leaking gas can settle in any low

areas or confined spaces.

 Propane gas odorant may fade, mak-

ing the gas undetectable except with

a warning device.

If the presence of gas is suspected, fol-

low these instructions:

 Do not try to light any appliance.

 Do not touch any electrical switch;

do not use any phone in your build-

ing.

 Immediately call your gas supplier

from a neighbors phone. Follow the

gas suppliers instructions.

 If you cannot reach your gas sup-

plier, call the fire department.

This kit includes: installation instructions, propane ori-

fices, valve conversion kits with instructions, conver-

sion rating plate, conversion date certificate, wire ties,

and screen/turbulator removal warning tag.

Installation

CAUTION

PERSONAL INJURY HAZARD

The gas supply must be shut off prior to

disconnecting the electrical power, be-

fore proceeding with the conversion.

1. Remove the gas manifold by removing the burner

box front cover (not required on all models), cutting

the wire ties, disconnecting the gas valve low volt-

age wires, and removing the four manifold mount-

ing screws. See Figure 1.

Figure 1

Gas Manifold Removal

2. Replace natural gas orifices with the altitude appro-

priate propane orifices (Figure 2B) specified in Table

1. Tighten orifices with a box-end wrench. Do not

use a socket wrench, as it could damage the ori-

fices. Do not over-tighten. Do not cross thread.

Propane Gas Orifices

Standard Altitude Data High Altitude Data

Model

Kit

Number

Orifice

Altitude

(ft)

Pilot

Orifice

Kit

Number

Orifice

Altitude

(ft)

GUIA, GUIB

GCIA, GCIB

LPTK07A #55 0 - 7500 N/A HALP06 #56 7500 - 11000

GUIC

GCIC

LPTK07A #55 0 - 6000 N/A HALP06 #56 6000 - 11000

GUC, GUD

GUX, GDC

GCD, GCC

LPTK07A #55 0 - 4500 N/A HALP08 #56 4500 - 9500

PGB**C

PGD**C

LPTK07A #55 0 - 6000 BBR12 HALP06 #56 6000 - 9500

GUIS, GCIS

LPTK07A #55 0 - 2000* N/A N/A N/A N/A

* See the Amana Distributor for High Altitude Kits for installations above 2000 feet.

Table 1

1 2 3 4 5 6

Comentários a estes Manuais

Sem comentários

Amana PGD**C Manual de Instruções Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Aparelhos de ar condicionado "split system" Amana PGD**C